Back to Resins

 

 

 

 

 

4.151 GEMCOAT ES 2:1- LV

EPOXY RESIN FOR EMBEDDING & CASTING

 

 

  • Composition and Properties

  • GEMCOAT ES 2:1 LV is a low viscosity epoxy resin formulated for use as a hard, resistant, clear sealer for timber and other substrates (consult GemCo).

  • It is particularly suited to filling cavities up to 20mm deep in one pour due to its air release & low viscosity

  • It has been used by hobbyists , crafts , woodturners, electrical component manufacturers etc.

  • Physical properties

  •  Appearance: Base - clear liquid Hardener - clear liquid

  • Odour: low odour

  • Flammability: non flammable

  • Solids: 100%

  • Coating Type: Epoxy

  • Packaging: 1,2,10, 20 litre two part pack & 200L drums

  • Mix ratio: 2:1(base : hardener)

  • Pot Life: Approximately 30 min @ 20 °Celsius (200g mix)

  • Coverage: 1 sq metre/litre @ 1 mm thickness ( typical - depends on substrate)

  • Dry to Recoat: Typically overnight - will vary according to temperature & humidity.

  • Tensile strength:* 3000 psi

  • Compressive strength* 7000 psi

  • Shore hardness:* 70 *typical value

  • Surface Preparation

  • Test patch is recommended on a new substrate or if the product has not been used before.

  • All surfaces to be clean, dry, and free of loose material.

  • Thoroughly solvent wipe wooden surfaces to remove any oily deposits and allow to dry.

  • Method of Application

  • For best results store , apply, & cure resin at temperature of 25 ° C.

  • Add 1 part hardener to 2 parts base (by volume) and thoroughly hand mix .

  • Hand mix small quantities with a stick taking care to scrape sides & bottom of container then allow to sit for a few minutes for air to come out - watch pot life.

  • Pour in to cavity to be filled and leave product to self level then use a gas flame or heat gun (if required) waved gently over the surface to release any air bubbles.

  • Allow to cure in a dust free environment. The product can be cut and polished although the finish is often good enough without this.

  • Cutting & Polishing - wet sand with 600 then 1200 grit paper until a uniformly flat surface is achieved. Buff with 3M Perfect It III 5958 cutting compound (or equivalent) until level of gloss required is achieved. A coat of 3M Perfect-It III polish (or equivalent such as Diamond Cutting Compound 2.0) can be applied to give a very high gloss finish.

  • Note: GEMCOAT ES 2:1 LV can be used on bar & table tops but GEMCOAT ES 1:1 is better suited to this type of use

  • Handling Precautions

  • Avoid contact with eyes and skin.

  • Do not ingest.

  • Use with adequate ventilation.

  • Protective clothing ,eye protection, and gloves should be worn.

  • Do not breathe vapor or spray.

  • Keep away from children.

1/3/98

 

The information provided is accurate to the best of our knowledge. We can not however anticipate all conditions under which this information and our products may be used. We therefore accept no responsibility for results obtained by the application of our products, or for their safe use and suitability. GemCo Limited sells these products without warranty and buyers and users assume all responsibility and liability for loss or damage arising from the handling and use of our products.

 

 

63 Hewletts Rd, Mt Maunganui. P.O. Box 4274, Mt Maunganui South, New Zealand.

Phone +64 7 572 2411 Fax +64 7 572 2415 E-Mail info@gemco.net.nz

 Website: www.gemco.net.nz